Learning the Basics of Installing a Bathtub
Learning the Basics of Installing a Bathtub
Blog Article
We've noticed the article on How to Install a Bathtub Yourself directly below on the internet and decided it made sense to share it with you in this article.
Setting up a bathtub isn't precisely rocket science, but it does call for solid plumbing, woodworking, and in some cases, tiling abilities. Changing an old bathtub with a new one is also a moderately challenging project. If the old tub is conveniently easily accessible, the project can move easily; if you need to open a wall to remove the old tub as well as position the brand-new bathtub, the task is much harder. In either case, the job is within a house handyman's skills, although you will certainly need a helper to move out the old tub and also set in the brand-new one. Ensure you have actually qualified on your own for the work and fit trying it. As opposed to employing a contractor to take over a halfway-completed project, it is far better to think about employing one before you begin. Chances are you might need a specialist plumber to make tube links.
This post will assist you set up a new bathtub in your washroom if you have actually already purchased a brand-new tub and do not require to change the plan of your previous water system pipes.
Your devices and product checklist must make up the following:
Preparing for the Installment
To start with, the supporting structure supplied with the bath should be fitted (if needed) according to the producer's directions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is very important to make certain that if the tap features a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps device to avoid pressure on the bath tub.
Fit the adaptable tap connectors to the bottom of both taps utilizing 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should now be ready to be suited its last position.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you should do is detach the water. After doing so, turn on the faucets to drain any water remaining in the system. The process of eliminating the existing faucets can be quite problematic as a result of the restricted access that is usually the instance.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the faucets. Have a fabric all set for the continuing to be water that will certainly originate from the pipes. When the supply pipes have actually been removed, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from transforming during this process. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
Before going on to fit the new taps, compare the pipeline connections on the old taps to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Setting up the Bath tub
Using the two wood boards under its feet, put the bath tub in the needed position. The wood boards are valuable in evenly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four little points.
The next goal is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the spirit level and also adjusting the feet on the bath tub up until the spirit level checks out level.
To set up taps, fit the bottom of the outermost adaptable faucet adapter to the appropriate supply pipeline by making a compression join; then do the very same for the various other tap.
Switch on the water supply and inspect all joints and also new pipework for leaks and also tighten them if needed. Load the bath tub as well as likewise inspect the overflow outlet as well as the typical outlet for leaks.
Ultimately, take care of the bath paneling as explained in the producer's user's manual. Tiling and also securing around the bathtub should wait until the bathtub has actually been made use of at least when as this will certainly settle it right into its last position.
Fitting New Taps
If the tails of the new taps are plastic, after that you will require a plastic connector to stop damages to the string. One end of the connector fits on the plastic tail of the tap and the other end supplies a connection to the current supply pipelines.
If you require to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the mounting opening in the bath/basin making certain that the washing machines remain in place in between the faucet and the sink. Secure the faucet in position with the maker supplied backnut. When the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal tap ports. The previous kind ought to be connected to the faucet ends initially, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the location where the bath fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to break a rigid seal, triggering the water to penetrate the wall surface in between the bathroom as well as the tiling, resulting in issues with moisture and possible leaks to the ceiling below.
You can select from a variety of coloured sealants to assimilate your fixtures and also installations. They are offered in tubes as well as cartridges, as well as can securing spaces up to a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched newspaper or soft rope. Remember to constantly load the bathtub with water prior to securing, to permit the motion experienced when the tub is in use. The sealer can crack rather early if you do not take into consideration this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily readily available on the market. It is a good idea to fit the floor tiles utilizing waterproof or waterproof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was made aware of that report on Tools You Need to Install a New Bathtub from a friend on our other site. Enjoyed our entry? Please share it. Help others find it. Thanks so much for taking the time to read it.
Hot water issue? Call! Report this page